Re: Error while adding new node

Murtuja,

As crazy as this sounds, I've had a similar issues 2-3 years ago and the problem was the ssh keys were installed to allow for non-password logins. When I removed that configuration (authorized_keys) the add node worked. After the node was added I could put the ssh config back in place. I know it sounds crazy. This was on 10.2.0.1 on Solaris.

Finn

On Mon, Apr 28, 2008 at 1:28 AM, Murtuja Khokhar <mkhokhar_at_indorion.com> wrote:

> Hi Krish,
>
>
>
> I have checked from /etc/ssh/ssh_config and /etc/ssh/ssh_config. X11
> forwarding is set to *no*.
>
>
>
> Thanks for reply
>
>
>
> Regards,
>
> Murtuja Khokhar
>
> Oracle Database Administrator
>
> *Ind**orion Networks Pvt. Ltd.***
>
> Lower Level, Tower A (Mateen Tower)
>
> Diamond District
>
> 150 Airport Road, Bangalore 560008 India
>
> Email:mkhokhar_at_indorion.com <Email%3Amkhokhar_at_indorion.com>
>
> Office: +91 80 414 72000
>
> Extension: 1115
>
> Mobile: +91 98865 57151
>
> Fax: +91 80 414 72050
>
>
>
> *From:* krish.hariharan_at_quasardb.com [mailto:krish.hariharan_at_quasardb.com]
>
> *Sent:* Monday, April 28, 2008 11:07 AM
> *To:* Murtuja Khokhar; oracle-l_at_freelists.org
> *Subject:* RE: Error while adding new node
>
>
>
> A long shot – verify that X11 forwarding is no in the ssh_config files of
> both nodes. I have had problems with that before where internode
> connectivity is affected (I believe that there is a ML note on that). I
> would suspect that the second message is as a consequence of the first, but
> regardless, resolving the first error would verify that.
>
>
>
> -Krish
>
>
> ------------------------------
>
> *From:* oracle-l-bounce_at_freelists.org [mailto:
> oracle-l-bounce_at_freelists.org] *On Behalf Of *Murtuja Khokhar
> *Sent:* Sunday, April 27, 2008 10:34 PM
> *To:* oracle-l_at_freelists.org
> *Subject:* Error while adding new node
>
>
>
> Hi,
>
>
>
> I have two node RAC setup. I am using Oracle 10g Standard Edition
> (10.2.0.3.0) on Solaris 10 (sparc 64bit).
>
> I am testing node crash scenario so I have deleted one node. I have
> followed steps from ML#269320.1.After deleting node successfully I have
> tried to add node. For adding node I have followed ML#270512.1
>
>
>
> When I started to add new node, I was able to add clusterware to new node.
> VIPCA was successful.
>
> but when I tried to add Oracle Software on new node ,I am getting error
> message like "The selected remote nodes are not accessible" and "The
> virtual host name for node is already in use"
>
>
>
> For troubleshoot this error :
>
>
>
> I have checked user equivalence (SSH) is OK and All nodes can ping each
> other.
>
> vip is configured properly and both are on eri0:1 and I can ping both vip
> from each node.
>
>
>
> Can you please suggest me fix for this error?
>
>
>

--
http://www.freelists.org/webpage/oracle-l